Which transmission cooler line goes where on a 2001 dodge ram going to transmission?

Adolfo Schulist asked a question: Which transmission cooler line goes where on a 2001 dodge ram going to transmission?
Asked By: Adolfo Schulist
Date created: Sat, May 29, 2021 11:13 PM

Content

FAQ

Those who are looking for an answer to the question «Which transmission cooler line goes where on a 2001 dodge ram going to transmission?» often ask the following questions:

❗ Does it matter which transmission cooler line goes where?

Fluid is full. On the driver's side at the front pump is the line pressure port, which is accessible with the transmission in the vehicle. Putting the cooler where it gets lots of air thru it is the important part. The line probably goes from the transmission to the radiator.

❗ How do you change a 2001 dodge dakota auto transmission oil cooler?

remove fan and shroud, take off upper and lower radiator hoses. remove 4 bolts holding guard to radiator. pull on shroud and fan at the same time. pull out 4 bolts holding radiator to frame of truck, lean radiator toward the engine and undo the 2 lines going into that small box on ur left and pull the 4 bolts holding it to the radiator and it should b out

❗ Where is the transmission cooler line located?

Metal transmission cooler lines are typically pre-bent with fittings that are held on by a flare at each end of the line. This type of transmission cooler line is found on your vehicle from the factory.

1 other answer

The pressure line is the one closer to the front.The pressure line is the one closer to the front.

Your Answer

We've handpicked 24 related questions for you, similar to «Which transmission cooler line goes where on a 2001 dodge ram going to transmission?» so you can surely find the answer!

What size are transmission cooler line fittings?

Transmission Radiator end of fitting has 1/4" MPT. line fitting is 1/2"-20 inverted flare INS. - Factory fitting remains with recessed internal threads.

Read more

Do you need a transmission cooler on a dodge ram?

  • I have since added 4.56 gears, 3000 stall converter, 180* stat, and Mag Hytec transmission pan. Since these mods, it has never gone over 155*. OP also has a 180* stat. Simple point is that an additional cooler is not needed on the 4th gens. I only know 1 person that has cooked his transmission fluid on a 4th gen...you know him too.

Read more

Where is the transmission cooler line on a 1988 honda prelude?

If it is a manual transmission you do not have transmission cooler lines. If its an automatic they will be on one side of the radiator and you can follow them to the tranny from there.

Read more

How do you change a transmission cooler line?

  1. Raise the Vehicle. It would be best to work on level ground to ensure that your vehicle does not lean too much on the jack when lifted…
  2. Drain the Transmission Fluid…
  3. Remove the Old Line…
  4. Install the New Cooler Line…
  5. Replenish the Transmission Fluid…
  6. Double-check.

Read more

How do you remove cooler line from transmission?

  • Unscrew the fittings. Remove cooler line from transmission fitting. Pull the line out of the transmission fitting, taking care not to bend the line. The line is usually made of steel, ranging in width from 5/16-inch to 3/8-inch with a flare nut on the end. It can be up to 5 feet in length, but it depends on the type of car.

Read more

How much does a transmission cooler line cost?

The average cost for trans oil cooler line replacement is between $219 and $245. Labor costs are estimated between $100 and $126 while parts are priced at $118. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

Read more

Is the cooler line on a transmission replaceable?

  • Yes, but only the ones in the transmission. The connectors on the cooler are integral, and are not replaceable. Yeah I meant that haha. Its not leaking at the cooler behind the grill, its perfectly clean, its leaking at the female connector to the tranny.

Read more

What does the automatic transmission cooler line do?

transmission cooler flow direction 4l60e transmission cooler lines diagram

The transmission cooling line system is vital to any automatic transmission. It circulates the hot fluid away to the radiator via cooler lines and returns the cooled fluid back to the transmission. A loss of fluid leading to an overheated transmission can be devastating as the system loses its ability to cool.

Read more

Is there a difference between 1969-1972 dodge transmission cooler lines?

Cooler lines should fit.Check and see if you have a 904 or 727 transmission. It should work fine, Good luck.

Read more

Which line is the return oil cooler line?

rev tec oil lines diagram

Read more

How do you connect transmission cooler line to radiator on dodge ram 1500 do i need to get a new line were it is crimped?

you will need a disconnect tool for fuel/ac. not sure exactly on the size. with the tool you'll push in at the bigger end of the tube (with the tool on the smaller tube) and with a little wiggling it will break free

Read more

Do you need a transmission cooler 1500 dodge ram 4x4 5.9 360?

If you are going to do any towing, it is recommended to add an additional cooler.If you are going to do any towing, it is recommended to add an additional cooler.

Read more

Should you add a transmission cooler when you replace a transmission on a 1996 dodge caravan?

Not a bad idea especially if you are either hauling a trailer or in a warm climate or have a lot of hills - certainly won't hurt

Read more

How does kooler kleen transmission line flush cooler work?

  • This product works with out any water to remove grease, dirt, grime, and metal shavings that can clog up the lines. And it inhibits their return. Because of its unique solvent formulation, it will not degrade new automatic transmission fluid.

Read more

How much pressure is in a transmission cooler line?

cooler bypass valve transmission cooler flow direction

there is at idle between 20-50 psi but during use pressures in transmission lines can reach 100 psi or more. if you are going to use rubber lines be sure to use barbed fittings so the hose does not blow off. Cooler and lube pressure are about the same at 5-30 psi.

Read more

Where is the transmission cooler?

  • In a down-flow radiator, the transmission oil cooler is located in the bottom portion of the radiator. In a cross-flow radiator, the transmission oil cooler is located in the side of the radiator. • Transmission oil cooler assemblies consist of metal tubing or an assembly of metal tubing and rubber hose.

Read more

Where is transmission cooler located?

  • The transmission cooler is inside the radiator; a leak will result in transmission fluid swirling around in the radiator's neck. It also results in pink, milky transmission fluid.

Read more

Where to install transmission cooler?

  • On the majority of vehicles the ideal location to install your transmission cooler would be to mount the cooler in front of your vehicle's radiator (position A in the picture). At this location, the cooler will be able to work more efficiently than installed behind the A/C condenser or behind the radiator.

Read more

Where to mount transmission cooler?

  • Transmission Cooler Mounting Position. When installing a transmission cooler, it is typically recommended to mount it in a location that gets a significant amount of airflow. Based on this, the best place to mount a cooler would be in front of the air conditioning condenser.

Read more

Do you need a return line for a transmission cooler?

  • If you plan to use rubber transmission hose and keep the stock cooler lines, you need to connect the cooler return line to your vehicle’s return line. In most cases you’ll need to make a cut to the factory line and connect the new rubber line to it.

Read more

How do you use the transmission cooler line disconnect tool?

Use 1/2" size for Ford Super Duty Trucks, F250, F350 and F450. Tip is specially stepped to fit connector. Simply push the line toward the connector, then engage tool and pull line from connector. Set comes skin packed with a bead chain.

Read more

How much pressure should be on a transmission cooler line?

there is at idle between 20-50 psi but during use pressures in transmission lines can reach 100 psi or more. if you are going to use rubber lines be sure to use barbed fittings so the hose does not blow off. Cooler and lube pressure are about the same at 5-30 psi.

Read more

Where is the transmission cooler located?

The cooler for the automatic transmissions are placed inside the radiator, the reason behind this is the antifreeze provides the perfect environment. It warms the transmission up with it's cold and keeps it from getting too hot in extreme heat.

Read more

Where is the transmission fluid cooler?

The transmission cooler is inside the radiator; a leak will result in transmission fluid swirling around in the radiator's neck. It also results in pink, milky transmission fluid.

Read more